Join Today
Enjoy an ad free experience by logging in. Not a member yet? Register.
Results 1 to 2 of 2
  1. #1
    Junior Member
    Join Date
    Jan 2010
    Posts
    14
    Thanks (Given)
    0
    Thanks (Received)
    0

    Default phone is in recovery mode and won't restore

    ok my Iphone was a 3.1.2. and i was going to restore and upgrade to 3.1.3 it got hung in recovery mode and wont do anything else is there something i can do to prevent this in the future? and also does anybody know why this happened?

  2. #2
    Senior Member
    Join Date
    Oct 2009
    Posts
    7,977
    Thanks (Given)
    0
    Thanks (Received)
    0

    Default Re: phone is in recovery mode and won't restore

    Hi mate, sometimes it just does this. I have also experienced this. So you mean to say you have solved the problem? If not, kindly look below.

    Quote Originally Posted by Pece1976
    Recovery Mode : Recovery Mode is a state of iBoot that is used during standard upgrades and restores. As iBoot is active, it does not allow you to downgrade your device’s software. Also, unless it is ‘pwned,’ it will not allow custom firmware to be flashed.

    DFU Mode : DFU Mode is a special mode where the device can still interface with iTunes, yet it does not load the iBoot. The screen will appear totally black in DFU mode, so you can’t guess whether the device is in DFU or powered down from simply looking at the screen. Because iBoot and the OS are not loaded this exploit makes us able to downgrade your iPhone firmware or upgrade with a custom firmware created by Pwnage tool.

    How to put your iPhone in recovery mode :

    1.Turn the device completely off and disconnect it from cable/dock.
    2.Hold down the home button.
    3.While holding down the home button connect to a computer with a cable (easiest) or dock.
    4.Keep holding down the home button until you see a connect-to-itunes screen You are now in recovery mode.

    To escape Recovery Mode and power the phone off simply hold down power and home buttons for ten seconds.

    How to put your iPhone in DFU mode :

    1.Connect your iPhone to your computer.
    2.Turn iPhone off.
    3.Hold power and home together for 10 seconds (exactly).
    4.Release power but keep holding home until the computers beeps (observed on a PC) as a USB device is recognized.
    5.A few seconds later iTunes should detect your iPhone.
    6.If the Restore Logo is present on the screen, you are in Recovery Mode, not DFU

    You can get out of DFU mode by holding down the home button and the power button for about 10 seconds. If your phone is connected to your computer you'll hear a beep as when a USB device is disconnected. Then just press the power button and your phone will start up as usual.


 

Similar Threads

  1. Guide: Nokia 5800 security code recovery after firmware flash
    By nasua in forum Symbian S60v5 Firmware Discussion
    Replies: 68
    Last Post: 03-03-2013, 05:49 AM
  2. Recovery Mode and DFU Mode
    By pece1976 in forum iPhone Forum
    Replies: 1
    Last Post: 06-22-2012, 09:28 AM
  3. Flashing problems (phone wont boot into flash mode)
    By rocker9455 in forum Symbian S60v5 Firmware Discussion
    Replies: 1
    Last Post: 06-23-2010, 02:40 PM
  4. Tap mode added & turning mode removed in sensor settings
    By NP in forum Symbian S60V5 Modding
    Replies: 3
    Last Post: 04-04-2010, 11:31 AM
  5. Phone restarts when switched to mass storage mode
    By lordvoldemort8 in forum Symbian S60v5 Forum
    Replies: 2
    Last Post: 02-04-2010, 05:26 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •